The PVC 90 Degree Elbow is a versatile and essential component for a variety of pipe installations. Made from durable PVC material, it is suitable for use in both sanitary plumbing and electrical systems. The elbow allows for a precise 90-degree change in direction for your pipe runs. It is available in multiple sizes, including 2×2, 3×3, and 4×4 inches, to accommodate different project needs.
| MATERIAL NAME: | UPVC Pipe and Fittings |
| PRODUCT USE: | Drain, Waste and Vent piping system |
| MANUFACTURER/SUPPLIER; FIGHTER LOCK PHILIPPINES CORPORATION | PREPARED BY: | Health, Safety and Environment |
| Unit 8 Green Miles Compound, Sitio Cabatuhan, Camalig Meycauayan, Bulacan | DATE PREPARED: | February 22nd 2015 |
This is not a “controlled product” under the Hazardous Products Act. UPVC is inert in all intended applications.
| INGREDIENT NAME | CAS NUMBER | APPROXIMATE CONCENTRATION % | LD50/LC50 | EXPOSURE LIMIT TLV ACGIH mg/m3 |
|---|---|---|---|---|
| UPVC Resin Blend | Not applicable | 100% | Not available | Not available |
| PHYSICAL STATE: | Solid |
| ODOR AND APPEARANCE: | orange, odorless |
| BOILING POINT: | 385°F (196°C) |
| FREEZING POINT: | Not applicable |
| VAPOR PRESSURE: | Not applicable |
| VAPOR DENSITY: | Not applicable |
| SPECIFIC GRAVITY: | 1.4 – 1.65 |
| pH: | Not applicable |
| ODOR THRESHOLD: | Not applicable |
| EVAPORATION RATE: | Not applicable |
| COEFFICIENT WATER/OIL DISTR: | Not applicable |
| FIRE FIGHTING: | Wear self-contained breathing apparatus (SCBA) equipped with a full face piece and operated in a pressure-demand mode or other positive-pressure mode and protective clothing. Personnel not having suitable respiratory protection must leave the area to prevent significant exposure to toxic gases from combustion, burning, or decomposition. In an enclosed or poorly ventilated area, wear SCBA during cleanup immediately after a fire as well as during the attack phase of fire fighting operations. Run off water from fire fighting may have corrosive effects. |
| EXTINGUISHING MEDIA: | Water spray, carbon dioxide, foam, dry chemical |
| HAZARDOUS COMBUSTION PRODUCTS: | Hydrogen Chloride, Carbon Dioxide, Carbon Monoxide, other substances dependent on fire conditions |
| FLASH POINT: | 734°F (390°C) approx. |
| LOWER FLAMMABLE LIMIT: | Not applicable. |
| UPPER FLAMMABLE LIMIT: | Not applicable. |
| AUTOIGNITION: | 800°F (425°C) (ASTM D-1929) approx. |
| CONDITIONS OF FLAMMABILITY: | Only if highly heated and exposed to a continuous source of ignition. UPVC pipe will not support combustion. |
| IMPACT SENSITIVITY: | Not available |
| STATIC DISCHARGE: | Not available |
| STABILITY: | Not available |
| REACTIVITY: | Not available |
| INCOMPATIBILITY WITH OTHER SUBSTANCES: | Not available |
| HAZARDOUS DECOMPOSITION: | See section 5 |
| EFFECTS OF ACUTE EXPOSURE TO PRODUCT: | No acute health effects reported with the inhalation of UPVC dust; dust may irritate the eyes. |
| EFFECTS OF CHRONIC EXPOSURE TO PRODUCT: | Vinyl resin is not known to cause any disease. Dust exposure should always be minimized. Routine inhalation of dust of any kind should be avoided. Exercise care when dumping bags, sweeping, mixing or doing other tasks which can create dust. |
| ROUTES OF ENTRY: | Inhalation, eye contact with dust (only when cutting or grinding) |
| SENSITIZATION: | None known |
| IRRITANCY: | Not available |
| CHRONIC/CARCINOGENICITY: | Not available |
| PERSONAL PROTECTIVE EQUIPMENT TO BE USED: | When cutting, the use of eye protection and a NIOSH-approved respirator for dust is recommended. |
| ENGINEERING CONTROLS TO BE USED: | Ventilate adequately when cutting. |
| WASTE DISPOSAL: | Handle in accordance with federal, state, provincial and municipal regulations. |
| PROCEDURES TO BE FOLLOWED IN CASE OF LEAK OR SPILL: | Pipe fragments and debris should be swept up and removed to a disposal container. |
| HANDLING PROCEDURES AND EQUIPMENT: | Avoid creating and breathing UPVC dust |
| STORAGE REQUIREMENTS: | None |
| SPECIAL SHIPPING INFORMATION: | Not applicable |
| SPECIFIC FIRST AID MEASURES: | No situation is likely to arise from routine handling of UPVC pipes. |
| EYES: | Remove particles with clean water. If irritation persists, consult a physician. |
| SKIN: | Wash with soap and water |
| INGESTION: | Do not induce vomiting; consult a physician. |
| INHALATION: | If irritation persists, consult a physician |
Disclaimer:
The information contained in this material safety data sheet is based on information available to Fighter Lock.
This specification covers uPVC S-1000 and S-600 Solid Wall Pipe and uPVC DWV Fitting used in sanitary drain, waste and vent (DWV), sewer and storm drainage piping applications. This system is intended in non-pressure applications where the operating temperature will not exceed 140° F.
Pipe shall be made and manufactured from virgin rigid PVC (polyvinyl chloride) vinyl compounds with a cell classification 0f 12454 as identified in ASTM D 1784. All pipe and fittings shall be manufactured in the Philippines. All systems shall utilized a separate waste and vent systems.
Installation shall comply with the latest installation instructions published or with supervision by Fighter Lock Philippines Corp. and shall conform to all applicable plumbing and building code requirements. Buried pipe shall be installed in accordance with ASTM D 2321. Solvent cement joints shall conform to ASTM D 2564. The system shall be protected from chemical agents not compatible with uPVC compounds. The system shall be tested after installation through leak test for 24 hours as much as possible.
PNS 1950:2003: Plastic piping systems for soil and waste discharge (Low & High temp.) inside buildings
– Unplasticised Polyvinyl Chloride (PVC-U)
ASTM D 2729: Standard Specification for Poly (Vinyl Choride) (PVC) Sewer Pipe and Fittings
ASTM D 1784: Specification for Rigid Poly (Vinyl Chloride) (PVC) Compounds and
Chlorinated Poly (Vinyl Chloride) (CPVC) Compounds
